Failure Analysis of Capacitors and Inductors

Posted by doEEEt Media Group
On October 19, 2023
0

The goal of passive components’ failure analysis (FA) is to determine the root cause for an electrical failure. The findings can be used by the manufacturers to improve upon the design, materials, and processes used to create their components. This leads to better quality and higher reliability components. The FA also provides feedback for the users to improve their handling, storage, and applications of these components.

ENGINEERING AND PROJECT MANAGEMENT SUPPORT

Pre-Procurement

Posted by Susana Galdeano
On May 3, 2022
0

The pre-procurement phase combines the EEE parts state-of-the-art analysis, risk analysis and component ownership cost optimization with regards to the mission requirements, design criticality and budget. In order to achieve this, the project manager leading a multidisciplinary team must find the optimal balance between component information availability (traceability, materials, testing, previous use…) and minimum tests to perform, reaching an acceptable level of reliability covering the technical, schedule and costing constraints.

INSPECTION, ELECTRICAL & VERIFICATION

X-Ray Inspection applied to Screening Test

Posted by doEEEt Media Group
On April 26, 2022
0

Screening procedures assist in achieving quality and reliability levels commensurate with the intended application. The screening test does not increase the reliability of the components but removes those showing weakness or defects.

INSPECTION, ELECTRICAL & VERIFICATION

Characteristics of X-RAY Inspection

Posted by doEEEt Media Group
On April 26, 2022
0

Radiographic inspection is based on X-ray radiation. This radiation can be produced by accelerating electrons under a certain voltage in a vacuum tube so that they are emitted from a cathode and collide into an anode called ‘target’ producing X-rays.

INSPECTION, ELECTRICAL & VERIFICATION

X-Ray Inspection applied to DPA test

Posted by doEEEt Media Group
On April 26, 2022
0

During the DPA test, parts go through a systematic and detailed examination at different levels of disassembly. It is important to note that DPA is not a test itself, but rather a comprehensive series of tests where parts are examined for a wide variety of design, workmanship, and processing problems.

INSPECTION, ELECTRICAL & VERIFICATION

Constructional Analysis Tests

Posted by doEEEt Media Group
On April 26, 2022
0

Constructional Analysis as a complete service provides a deep understanding of the technologies used during the manufacturing process, information about the construction of their device

INSPECTION, ELECTRICAL & VERIFICATION

Scanning Acoustic Microscopy (SAM) and X-Ray Tomography

Posted by doEEEt Media Group
On April 26, 2022
0

The Scanning Acoustic Microscopy (SAM) technique is the most effective and complete non-destructive approach for the detection of critical and latent anomalies within plastic encapsulated parts, either on assembled or non-assembled systems

INSPECTION, ELECTRICAL & VERIFICATION, TESTING

Thickness Verification. An Introduction on HI-REL

Posted by Emilio Cano García
On April 10, 2022
0

Coating Thickness Verification The thickness of metallic coatings is routinely determined by X-ray fluorescence spectrometry. This provides a basis for assessing the quality of coated materials and therefore influences decisions regarding disposition (acceptability) of the coated product as well as control of coating processes.

EEE Components, PASSIVES

Ohmcraft Resistor Dividers Enable Innovative Downhole X-ray Inspections

Posted by doEEEt Media Group
On October 26, 2021
0

Exxelia Ohmcraft has provided custom resistors for petrotechnical analysis equipment used in downhole drilling. That’s why manufacturers of the downhole X-ray inspection platform turned to Ohmcraft to help develop a custom solution for use in this new and innovative diagnostic tool, which has already generated significant demand in the market.

ACTIVES, EEE Components

Electronic components for motor vehicles: the solution in New Space?

Posted by Demetrio López
On September 16, 2021
0

There are well-known advantages to using these photonic technologies in space, such as the limited generation of noise, electromagnetic immunity,

Page 1 of 312 3